Updated November 2026

Shopping for cordless drill alternatives Milwaukee users often look at when a standard drill is not quite enough. For most readers, the right answer depends on the job: a Milwaukee M18 impact driver wins for driving screws and lag bolts, while a hammer drill suits masonry, and a right angle drill handles tight spaces. A standard cordless drill still covers the widest range of general tasks.

Criteria Standard Cordless Drill Impact Driver Hammer Drill Right Angle Drill
Best for General drilling and driving Fast fastening, lag bolts Concrete and masonry Tight or awkward spaces
Torque delivery Steady, adjustable clutch Rotational impacts Rotation plus hammering Steady, limited clearance
Chuck type Keyless chuck 1/4-inch hex quick-change Keyless chuck Keyless chuck
Clutch settings Yes, multiple Usually none Yes, multiple Yes, multiple
Size and reach Compact Compact, short Bulkier Slim head

Driving Power and Fastening

An impact driver delivers short rotational bursts that keep screws from camming out and make quick work of long fasteners. Manufacturers typically rate impact drivers by maximum torque, and that figure is usually higher than a standard drill of the same voltage. For repetitive framing or deck work, the impact driver is the clear winner. A standard drill still wins when you need a clutch to protect delicate screws or work in soft material.

Drilling Into Masonry and Concrete

A hammer drill adds a fast, percussive hammering action on top of rotation, which lets it chew through brick, block and concrete without a separate tool. Standard drills stall or overheat in these materials, so they are poor substitutes here. The trade-off is weight and bit selection: you need carbide masonry bits, and a hammer drill is not ideal for fine woodworking. For masonry, the hammer drill wins outright.

Reaching Tight Spaces

A right angle drill uses a geared head to work where a straight drill cannot fit, such as inside cabinets, between joists or beside walls. Its reduced reach and slimmer profile make it less comfortable for long drilling sessions. For confined work, the right angle drill is the better choice, though it is a specialty tool rather than a daily driver.

Pros & Cons

  • Impact driver: Pro: very high fastening speed. Pro: resists cam-out. Con: no clutch, which can over-drive small screws.
  • Hammer drill: Pro: drills masonry without extra tools. Pro: strong, consistent hole drilling in concrete. Con: heavier and louder than a standard drill.
  • Right angle drill: Pro: reaches confined areas. Pro: compact head for close quarters. Con: limited reach and a narrower range of uses.

Which Should You Choose?

  • Choose an impact driver if you mostly drive screws and lag bolts for framing, decking or assembly. View on Amazon
  • Choose a hammer drill if you regularly drill into brick, block or concrete. View on Amazon
  • Choose a right angle drill if you often work inside cabinets, between studs or in other confined spaces. View on Amazon

For readers who want a broader starting point, the Milwaukee Cordless Power Drill: How to Choose and Use One Right guide covers general-purpose options, and the Milwaukee Impact Drill Cordless: How to Choose and Use One Right article explains how impact-style drills differ from driver models.

FAQ

Can an impact driver replace a cordless drill?

For driving fasteners, usually yes. For drilling precise holes, using a clutch on delicate materials, or working with drill bits that need steady torque, a standard drill is the better tool. Many shops keep both.

Do I need a hammer drill for occasional masonry work?

Not always. Small anchor holes in mortar joints or softer block can sometimes be drilled with a standard drill and carbide bits, but it is slow and can overheat the motor. Frequent or deep holes in concrete justify a hammer drill.

Is a right angle drill worth owning?

If you regularly work in tight spaces, yes. Otherwise, a standard drill with an extension or a flexible bit holder may handle occasional tight-space jobs. Always check manufacturer guidance on bit and accessory compatibility before buying.

Conclusion

No single tool replaces every option, so match the choice to your main work: impact drivers for fastening, hammer drills for masonry, and right angle drills for confined spaces. A standard drill remains the most versatile starting point. When in doubt, consult the manufacturer’s specifications for torque, voltage and accessory compatibility.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our power tools guides, checking product details against manufacturer specifications and owner feedback.