Updated November 2026

A circular saw for cutting 4×4 lumber can make clean, square cuts through a post in a few passes, provided you support the wood properly and set the blade depth correctly. This guide walks through setup, marking, the cutting technique for a true 3.5-inch by 3.5-inch post, and the mistakes that most often ruin the cut. The method works for pressure-treated and untreated dimensional lumber alike.

Choose the Right Blade and Set the Depth

A 4×4 measures 3.5 inches on each side, so the blade has to reach past that to clear the wood fully. Most 7-1/4-inch circular saws cut about 2-1/2 inches at 90 degrees, which means you will need to make two passes, one from each side. Set the blade depth so the teeth extend roughly 1/4 inch below the bottom of the board. Any deeper and you increase kickback risk and tear-out without gaining anything.

Shopping for one? See our guide: 5 Best DeWalt Circular Saw Battery Options for Cordless Cutting (2026).

For framing-grade lumber, a 24-tooth carbide-tipped framing blade cuts fast and tolerates grit in pressure-treated wood. A 40-tooth combination blade gives a smoother edge if the cut will be visible. Check the blade for damage and confirm it is rated for the saw’s maximum RPM before you start.

Mark and Support the Post

Use a speed square to draw a line all the way around all four faces of the post. Carry the line across the top and down each side so you have a continuous guide. Then clamp the 4×4 to a sawhorse or workbench with the cut line hanging just past the support edge, so the waste piece does not pinch the blade.

  1. Confirm the blade is unplugged or the battery is removed before adjusting anything.
  2. Set the depth to about 2-3/4 inches for a 2-1/2 inch cut capacity, or as needed for your saw.
  3. Place the saw’s base plate flat on the wood and align the blade just outside the line on the waste side.
  4. Start the saw, let it reach full speed, then advance steadily without forcing it.
  5. Stop when the blade reaches the depth mark. Let the blade stop fully before lifting the saw.
  6. Flip the post 180 degrees and repeat the pass from the opposite side, lining up on the same marks.

Make the Second Pass Accurate

The second pass is where most cuts go wrong. Use a speed square or a short straightedge to check that your blade is still on the line from the first cut. If the first pass left a slight angle, correct it on the second pass rather than forcing the saw. For long, repeatable cuts, clamp a straight guide to the post so the base plate runs against it.

Once both passes are complete, the piece should separate cleanly. If a small bridge of wood remains, finish it with a handsaw rather than pushing the circular saw deeper.

Common Mistakes

  • Cutting with the post unsupported, which lets the waste piece pinch the blade and cause kickback.
  • Setting the depth too deep, which exposes more blade than needed and increases the chance of binding.
  • Forcing the saw through the cut instead of letting the blade do the work.
  • Standing directly behind the blade line. Keep your body to the side of the saw path.
  • Skipping the second pass alignment check, which often leaves a visible angle on the joint.

A stable support setup makes the biggest difference for repeatable cuts. Adjustable sawhorses hold the post at a comfortable working height and keep the cut line clear of the supports. View on Amazon

A rafter square or speed square keeps your marks true on all four faces. View on Amazon

A clamp-on straight edge guide helps the base plate track a consistent line on both passes. View on Amazon

FAQ

Can you cut a 4×4 in one pass with a circular saw?

Most standard 7-1/4-inch circular saws cannot cut through a full 3.5-inch 4×4 in one pass. Plan on two passes from opposite sides, or use a larger saw or a plunge-capable tool if your model supports deeper cuts.

Do I need a special blade for pressure-treated 4x4s?

A carbide-tipped blade handles pressure-treated wood better than a standard steel-tipped blade. Expect the teeth to dull faster because treated lumber contains grit and chemicals that wear edges.

Is it safe to hold the post by hand while cutting?

No. Clamp or secure the post firmly to a support so it cannot move or pinch the blade. If you are unsure about setting up a safe cut, consult an experienced carpenter or follow your saw manufacturer’s guidance.

Conclusion

With the right blade, a secure support and a two-pass method, a circular saw can produce clean 4×4 cuts suitable for framing and outdoor projects. Take your time on the second pass, check alignment, and never let the blade bind. Practice on scrap first if you are new to the technique.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our power tools guides, checking product details against manufacturer specifications and owner feedback.