Updated November 2026

Metal cutting oscillating tool blades let you cut sheet metal, conduit, screws, nails and flush trim in tight spaces where a hacksaw or a full-size saw won’t fit. Choosing the right blade comes down to the metal you’re cutting, the blade material and tooth style, and how you run the tool. This guide walks through each decision so your cuts stay clean and your blades last longer.

Step 1: Match the Blade to the Metal

Start with the material. Thin sheet steel, copper pipe, aluminum and cast iron each respond differently to tooth design, so the blade you use for one may chew up another.

Shopping for one? See our guide: 7 Best Milwaukee Tools Circular Saw Models for Jobsite and Home Use (2026).

  • Ferrous metals (steel, stainless, cast iron): Choose bi-metal or carbide-grit blades. Bi-metal blades suit general steel and fasteners; carbide grit handles hardened or stainless material.
  • Non-ferrous metals (aluminum, copper, brass): Use fine-tooth blades with generous gullets. Coarse teeth tend to grab and pull soft metal.
  • Thin sheet metal: Pick a fine-tooth blade so at least two or three teeth stay in contact with the workpiece at once.

Step 2: Pick the Blade Material and Tooth Style

Blade material sets how long the edge holds up under heat and friction. Bi-metal blades combine a flexible steel back with high-speed steel teeth, which resists wear and flexing. Carbide-grit blades bond abrasive particles to the edge and are typically used for stainless steel, hardened fasteners and tile-adjacent metal work. Plain high-carbon steel blades are fine for light, occasional use on soft metal but dull quickly on anything tougher.

Tooth style matters too. Fine teeth (roughly 24 to 32 teeth per inch) give smoother, slower cuts in thin stock. Coarser teeth remove material faster but leave a rougher edge and are better suited to thicker pieces.

Step 3: Set Up the Cut Correctly

Before you cut, confirm the blade is seated fully in the tool’s clamp and tightened to the manufacturer’s torque or hand-tight specification. A loose blade wobbles and breaks. Use the lowest speed setting that still moves the material; most metal cutting is done in the lower to middle speed range. Keep the blade flat against the work, let the oscillation do the cutting, and avoid forcing it.

  1. Clamp or support the metal so it cannot vibrate or shift.
  2. Mark your cut line and, on sheet metal, start with a plunge if the blade allows it.
  3. Run the tool at low speed to establish the kerf before increasing speed.
  4. Use light, steady pressure and let the blade cool periodically on long cuts.

Step 4: Check Blade Condition and Replace on Time

A dull or overheated blade shows up as blued or discolored teeth, slow progress and burning smell. Heat is the usual cause of early failure, so reduce speed or pressure rather than pushing harder. Replace the blade when it stops cutting cleanly, when teeth are missing, or when it has been overheated enough to change color.

Common Mistakes to Avoid

  • Using a coarse-tooth wood blade on metal, which clogs and dulls quickly.
  • Running at full speed on thin sheet, causing the metal to chatter and the teeth to skip.
  • Forcing the cut instead of letting the blade work, which generates heat and bends the blade.
  • Skipping a check of the blade clamp before starting, leading to loose blades and kickback.
  • Cutting without eye protection; metal shards and burrs fly off unpredictably.

A bi-metal assortment pack covers most common metal jobs without buying blades one at a time. View on Amazon

Carbide-grit blades are the usual choice when you’re cutting stainless steel or hardened fasteners regularly. View on Amazon

Safety glasses keep metal chips out of your eyes during overhead or plunge cuts. View on Amazon

FAQ

Can I cut steel with a wood oscillating blade?

You can make a few light cuts in thin steel, but wood blades are not designed for metal and will dull or break quickly. Use a bi-metal or carbide-grit blade for steel.

How many teeth per inch do I need for thin sheet metal?

Fine-tooth blades in the roughly 24 to 32 teeth-per-inch range keep enough teeth in contact with thin stock to cut smoothly without grabbing. Check the blade packaging for the exact tooth count.

Why does my blade keep overheating?

Overheating usually comes from running too fast, pressing too hard or using a dull blade. Lower the speed, ease off pressure and let the blade cool during long cuts. Check the manufacturer’s guidance for your specific tool and blade.

Conclusion

Match the blade to your metal, choose the material and tooth count for the job, and run the tool at a controlled speed. Keep blades clamped securely and replace them when they stop cutting cleanly. For more on tool setup and accessories, see Oscillating Multi-Tools: Blades, Plunge Cuts and Sanding Attachments and Power Tool Accessory Maintenance Tips: 8 Habits That Extend Life.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our power tools guides, checking product details against manufacturer specifications and owner feedback.