Updated November 2026
Cutting aluminium with circular saw equipment is possible, but the blade you choose matters more than the saw. A dedicated non-ferrous metal blade with a high tooth count gives clean, controlled cuts, while a standard wood blade is faster to find but tends to grab, gum up and leave rough edges. If you cut aluminium only occasionally on thin stock, a good metal blade is usually enough. If you cut it regularly in structural or thicker sizes, a saw with a slower, more controllable motor and a guide system is the better investment.
| Criteria | Dedicated Metal-Cutting Blade | Standard Wood Blade |
|---|---|---|
| Cut quality on thin aluminium | Clean, burr-light edges | Rough, often chipped edges |
| Blade life | Holds up well when run at proper speed | Teeth dull or chip quickly |
| Kickback risk | Lower with slower feed and lubricant | Higher, because metal binds the teeth |
| Setup effort | Requires a blade swap | None, if you already own one |
| Best for | Regular or precision aluminium work | One-off, rough cuts |
Cut Quality and Finish
A dedicated non-ferrous blade, typically with 60 to 80 teeth on a 7-1/4 inch blade and a negative or low hook angle, produces a much cleaner edge. Manufacturers generally specify these blades for aluminium, copper and brass, and owners often report far fewer burrs compared with a wood blade. Winner: dedicated metal-cutting blade.
Safety and Kickback Control
Aluminium is soft enough to smear and pack into the gullet, which can cause the blade to bind and the saw to kick back. A metal blade with proper tooth geometry clears chips more predictably. Whichever blade you use, run the saw at full speed, feed steadily, and support the workpiece on both sides of the cut so the kerf does not close. Winner: dedicated metal-cutting blade. A related read: Straight Edge Circular Saw (2026): Which Should You Choose?.
Blade Life and Maintenance
Wood blades dull quickly when they hit aluminium, and a single cut can leave teeth chipped. A metal blade lasts longer on aluminium but still needs cleaning. Wipe away aluminium residue after each session, and use a cutting lubricant or a light coat of wax on the blade to reduce buildup. Winner: dedicated metal-cutting blade. For another angle, check out Cutting Aluminum with a Miter Saw (2026): Which Should You Choose?.
Speed and Convenience
A standard wood blade is already on most saws, so it wins for quick, rough cuts where a clean edge is not critical. You will still get slower, messier results, and you may need to file down burrs afterward. Winner: standard wood blade, for convenience only.
Pros & Cons
Dedicated metal-cutting blade
- Pro: Clean, precise cuts on thin aluminium sheet and extrusions.
- Pro: Lower kickback risk when run at proper speed with a steady feed.
- Con: Requires swapping blades and keeping a separate blade on hand.
Standard wood blade
- Pro: Already installed on most circular saws, so no extra purchase needed.
- Pro: Acceptable for rough, one-off cuts where edge finish does not matter.
- Con: Rough edges, faster dulling and a higher chance of binding.
Which Should You Choose?
- Choose a dedicated metal-cutting blade if you cut aluminium regularly, need clean edges for trim or panels, or want to reduce kickback. Pair it with a corded or cordless saw you already trust. View on Amazon
- Choose a standard wood blade if you only need a quick, rough cut on scrap aluminium and do not mind cleaning up the edge afterward. View on Amazon
For a broader look at blade selection and tooth count, see Saw Blades: Tooth Count, Kerf and Grind for Circular, Miter and Table Saws. If you are new to the saw itself, How to Cut Wood with Circular Saw: A Step-by-Step Guide for Beginners covers the fundamentals of setup and stance, which apply to metal cuts as well.
FAQ
Can I cut aluminium with a regular wood blade?
You can, but expect rough edges, faster blade wear and a greater risk of the blade binding. For anything beyond a rough cut, a non-ferrous metal blade is the better choice.
Should I use lubricant when cutting aluminium?
Yes. A cutting lubricant or a light coat of wax on the blade helps prevent aluminium from welding to the teeth. Manufacturers generally recommend this for metal cutting.
How do I keep the cut straight on aluminium?
Clamp the workpiece firmly, mark your line on both faces, and use a straight guide or clamped straightedge. How to Cut Straight with a Circular Saw explains the technique in more detail.
Conclusion
For most people cutting aluminium with circular saw equipment, a dedicated non-ferrous metal blade is the better choice because it gives cleaner edges and a safer cut. A standard wood blade is only worth using for rough, occasional work. Always wear eye protection, secure the workpiece, and keep the saw moving at a steady pace.

