Updated November 2026
The DeWalt 20V Max XR cordless hammer drill is built for drilling into masonry, concrete and block as well as wood and metal. This guide explains what the hammer function does, how to set up the drill for hard materials, and how to avoid the mistakes that wear out bits and batteries early. By the end, you will know how to pick the right bit, choose a sensible drilling routine and get clean holes without overheating the tool.
Understand What the Hammer Function Does
A hammer drill adds a rapid forward-and-back percussive motion to the normal rotation. That impact breaks up the material at the bit tip, which is why it works on concrete and brick where a standard drill would stall. On the DeWalt 20V Max XR hammer drill, you switch between drill-only mode for wood, metal and plastic, and hammer mode for masonry. Using hammer mode in wood is a common mistake: it chews up the material and can crack the bit.
Shopping for one? See our guide: 6 Best Dewalt 20v Max Xr Cordless Drills for Home Use (2026).
Set Up the Drill for Masonry Drilling
- Select a carbide-tipped masonry bit that matches your anchor diameter. Manufacturers typically recommend the bit be the same diameter as the anchor sleeve.
- Set the mode selector to hammer drill and the clutch to the drill (not driver) setting so the chuck does not slip.
- Choose a speed range suited to the bit size. Larger bits in masonry should run at a lower speed to reduce heat.
- Mark the hole location, then start the drill at low speed to create a small pilot dimple before increasing trigger pressure.
- Drill straight in with steady pressure. Let the hammer action do the work rather than leaning on the drill.
- Clear dust every few seconds by withdrawing the bit partway while it is still spinning.
Match the Bit and Battery to the Job
Bit selection matters as much as the drill itself. Use carbide masonry bits for concrete and brick, and twist bits or spade bits for wood. For wall anchors, check the anchor manufacturer’s specified hole depth, since a hole that is too shallow will not seat the anchor and one that is too deep will leave it loose.
| Material | Mode | Bit type |
|---|---|---|
| Wood | Drill only | Twist or spade bit |
| Metal | Drill only | HSS twist bit |
| Brick, block, concrete | Hammer drill | Carbide masonry bit |
For longer masonry sessions, carry a second battery. Heavy hammering draws more current, and owners often report that a fresh pack lasts noticeably longer than one that is already partly drained.
Common Mistakes
- Running hammer mode in wood or metal, which damages the bit and workpiece.
- Pressing too hard. Excess force stalls the motor and overheats the bit without speeding the hole.
- Skipping dust clearing, which glazes the bit and slows drilling.
- Using a worn bit. A dull carbide tip makes the drill work harder and heat up faster.
- Letting the battery run hot. Pause and let the pack cool if it becomes warm to the touch.
Recommended gear
A set of carbide masonry bits in the sizes you use most keeps holes clean and consistent. View on Amazon
A dust-clearing tool or small brush lets you clean the hole between passes without stopping the drill. View on Amazon
Depth stops or a drill depth gauge help you reach the same hole depth for every anchor in a project. View on Amazon
FAQ
Can I use hammer mode on wood?
No. Hammer mode is designed for masonry, and using it on wood can damage both the bit and the workpiece. Switch to drill-only mode for wood, metal and plastic.
What size bit should I use for wall anchors?
Match the bit diameter to the anchor sleeve as specified by the anchor manufacturer. Check the packaging for the recommended hole depth as well.
Why is my hole not getting deeper?
The bit is likely dull, clogged with dust or you are pressing too hard. Clear the hole, check the bit condition and let the hammer action do the work.
Conclusion
The DeWalt 20V Max XR cordless hammer drill performs best when you match the mode, bit and speed to the material you are drilling. Use hammer mode for masonry, drill-only mode for everything else, and clear dust regularly. Following these steps will give you cleaner holes and longer bit and battery life.

