Updated November 2026

DeWalt 20V oscillating tool accessories come in a few main families: saw blades, sanding pads, scrapers and grout tools. Matching the right accessory to the material and the cut you need makes the difference between a clean job and a burnt, wandering one. This guide walks through how to choose and fit them.

Know the Main Accessory Types

Most DeWalt 20V oscillating tool accessories fall into a few groups. Each one is built for a specific job, so start by naming the job before you pick a blade.

Shopping for one? See our guide: DeWalt vs Milwaukee Power Tools (2026): Which Is Better for Your Jobs?.

  • Plunge and flush-cut blades for trim, door jambs and cutting nails flush with a surface.
  • Bi-metal blades for wood with embedded nails and light metal work.
  • Carbide-grit blades for tile, grout and masonry-type materials.
  • Sanding pads and sheets for detail sanding in corners and tight spaces.
  • Scrapers for removing old caulk, adhesive and flooring.

If you are unsure which blade shape your tool takes, see DeWalt Oscillating Tool Blades: How to Choose and Swap the Right One for a fitting walkthrough.

How to Match an Accessory to the Material

  1. Identify the material: wood, drywall, metal, tile or grout.
  2. Check whether the material has hidden fasteners. Nails and screws call for bi-metal or carbide blades.
  3. Choose the blade width. Narrow blades handle tight curves; wider blades cut straighter.
  4. Set the speed dial low for tile and metal, and higher for wood.

For tile work specifically, carbide grit is the usual choice. Oscillating Tool Blade for Tile: How to Pick and Use the Right One covers grit and speed settings in more detail.

Fitting and Changing Accessories Safely

Always unplug the tool or remove the battery before changing an accessory. Most DeWalt oscillating tools use a tool-free clamp, so release the clamp, insert the accessory fully and tighten until it seats without play.

A loose accessory can vibrate off during use. Give the blade a firm tug after locking it in. Power Tool Accessory Maintenance Tips: 8 Habits That Extend Life has a few habits for keeping clamps and accessories in good shape.

Sanding and Scraping Attachments

Sanding pads work best in corners, around trim and on small curved surfaces that a full sander cannot reach. Use a light touch and let the oscillation do the work, because pressing hard burns through finishes quickly.

Scrapers remove old caulk and adhesive in tight joints. Keep the edge flat against the surface and move slowly so you do not gouge the substrate.

Common Mistakes

  • Using a wood blade on metal or tile, which dulls the teeth quickly.
  • Running the tool at full speed on materials that need slow, controlled cuts.
  • Forcing the blade into the cut instead of letting it work.
  • Skipping a check of the clamp before each use.
  • Ignoring worn or chipped blades, which cut poorly and can kick back.
  • DeWalt 20V oscillating multi-tool blades assortment gives you several blade shapes in one set, which suits people who switch between wood, metal and trim work. View on Amazon
  • DeWalt oscillating tool sanding pad set covers detail sanding with a range of grits for finishing corners and edges. View on Amazon
  • DeWalt carbide grout removal blade is built for cutting grout lines and tile without the rapid wear that bi-metal blades show on those materials. View on Amazon

FAQ

Are DeWalt 20V oscillating tool accessories interchangeable with other brands?

Not always. Many accessories use a universal shank, but clamp shapes and sizes vary by brand, so check the fit before buying.

Which blade should I use for cutting tile?

A carbide-grit blade is the usual choice for tile and grout. Use a slow speed setting and let the grit do the cutting.

How do I know when an accessory needs replacing?

Replace a blade when teeth are chipped, bent or dull, or when cuts start to wander or burn. Sanding pads should be swapped once they no longer cut or leave an even finish.

Conclusion

Choosing the right DeWalt 20V oscillating tool accessory comes down to the material, the cut and the fit. Match the blade to the job, set the speed to suit the material and check the clamp every time. Keep a small set on hand, and replace worn pieces before they slow you down.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our power tools guides, checking product details against manufacturer specifications and owner feedback.