Updated November 2026

To drill concrete with cordless drill, you need the right drill mode, carbide masonry bits, steady pressure and a plan for dust. A standard drill-only mode will stall or wander on concrete, but a hammer drill setting paired with a carbide bit lets you make clean holes for anchors, fasteners and small conduit runs. This guide walks through preparation, bit selection, drilling technique and finishing steps so your holes come out straight and your tool lasts.

What You Need Before You Start

Drilling concrete is harder on a tool than drilling wood or metal, so it pays to gather everything first. Interrupting a hole halfway through to hunt for a bit or a vacuum usually leads to a bent bit or a wandering hole.

Shopping for one? See our guide: Milwaukee M18 FUEL Cordless Hammer Drill: 9 Best Picks for Concrete and Masonry.

  • A cordless drill with a hammer drill mode (look for a dial or switch marked with a hammer icon)
  • Carbide-tipped masonry bits sized to your anchor or fastener
  • Fully charged batteries, plus a spare if the job is large
  • Safety glasses and hearing protection
  • A dust mask rated for silica (N95 or better) and a shop vacuum or drill-mounted dust extractor
  • A tape measure, pencil and center punch or nail for marking
  • Depth stop or a strip of painter’s tape wrapped on the bit as a depth gauge
  • A clean blow-out bulb or compressed air for clearing holes

Choose the Right Mode and Bit

Using the wrong mode is the most common reason people give up on cordless drilling in concrete. Standard drill mode rotates the bit only, which works poorly against aggregate. Hammer mode adds rapid forward impacts, breaking up the material while the bit turns.

Select hammer mode

Set the mode selector to the hammer icon before you touch the trigger. Most compact cordless drills use a single-speed hammer action, and many models offer a two-speed gearbox. For concrete, start in the lower gear, which delivers more torque and reduces bit walking.

Match the bit to the hole

Use carbide-tipped masonry bits, not standard high-speed steel bits. The bit diameter should match the anchor or fastener specification exactly, because a hole that is too large weakens the anchor grip. Manufacturers of common concrete anchors publish the required drill diameter and minimum embedment depth on the packaging, so check that data before you buy bits.

Check battery and chuck condition

Hammer drilling demands more current. A battery that is partly drained will fade quickly. Also confirm the chuck is tight and the bit is seated fully, since loose bits cause oval holes.

Step-by-Step: Drilling Your Hole

  1. Mark the location. Measure twice, then mark the center with a pencil. Make a small dimple with a center punch or nail so the bit does not skate across the surface.
  2. Set your depth. Measure the required embedment depth from the anchor instructions. Wrap a strip of painter’s tape around the bit at that distance from the tip, or use the drill’s depth stop.
  3. Position the drill. Hold the drill perpendicular to the surface. Use both hands, brace your elbows against your body and keep your feet set wide.
  4. Start slowly. Begin with light trigger pressure and let the bit bite into the dimple. Once it is seated, you can increase speed.
  5. Let the tool work. Apply steady forward pressure, but do not lean hard. Excess force overheats the bit, glazes the carbide and slows drilling.
  6. Clear the dust. Pull the bit partway out every 10 to 15 seconds, or when the flutes fill with dust. Keep the hole clean so the bit can keep cutting.
  7. Reach full depth. Stop when the tape reaches the surface. The hole should be slightly deeper than the anchor embedment to leave room for dust.
  8. Blow out the hole. Use a bulb or compressed air, then wipe the sides if you plan to set an adhesive anchor.

Dust Control and Safety

Concrete dust contains crystalline silica, which can cause lung damage with repeated exposure. Using a dust extractor or a vacuum attached to the work area is the most effective control. Wear a properly fitted respirator rated for silica when extraction is limited. If you have respiratory conditions or are unsure about exposure levels on a larger job, consult a professional or occupational safety resource before continuing.

Common Mistakes

  • Using drill-only mode. The bit spins without enough impact and the carbide overheats.
  • Pressing too hard. Force does not speed up concrete drilling and often causes the bit to bind or the battery to overheat.
  • Skipping hole cleaning. Dust packed in the bottom prevents anchors from seating and reduces holding strength.
  • Drilling into rebar. Use a rebar locator before marking if you are working on a structural slab.
  • Using a dull bit. A bit that smokes, squeals or drills very slowly needs replacing.
  • Running the battery flat. Swap batteries before they fade, since a weak pack produces uneven holes.

Tips for Better Results

  • Pre-drill tile with a regular bit in drill mode before switching to masonry work.
  • Keep the trigger pulled steadily instead of pumping it, which can cause the bit to skip.
  • Drill in short bursts for deep holes and let the bit and battery cool between holes.
  • Mark multiple holes with a template to keep spacing consistent across a wall.

A carbide masonry bit set gives you the sizes most anchor jobs require, and matched sizes help you avoid oversized holes. Carbide masonry bit set sizes are a practical starting point. View on Amazon

A depth stop attachment for your drill keeps holes consistent across repeated work. View on Amazon

A shop vacuum with a drill-mounted dust shroud captures dust at the source. View on Amazon

A silica-rated respirator protects your lungs during longer jobs. View on Amazon

If you are comparing hammer-capable drills before buying, see Cordless Drill with Hammer: How to Choose and Use One (Step-by-Step) for a breakdown of mode features. For concrete-specific picks, 6 Best Cordless Hammer Drills for Concrete Picks for 2026 covers several options. If you need to drill into tile or brick first, How to Drill into Tile, Brick and Concrete offers related technique notes. Those who prefer heavier-duty tools may find 7 Best Cordless Rotary Hammer Drills for Concrete and Masonry: Expert Picks useful. For a brand comparison, Milwaukee vs Dewalt Cordless Drill (2026): Which Should You Choose? lays out the differences.

FAQ

Can a cordless drill really drill concrete?

Yes, a cordless drill with hammer mode can drill small to medium holes in concrete, typically for anchors and fasteners. Large-diameter or very deep holes usually call for a rotary hammer.

What size bit do I need for a concrete anchor?

Use the diameter specified on the anchor packaging. Drilling oversized holes reduces holding strength, so match the size exactly.

Why is my bit smoking or glowing?

The bit is overheating, usually from excess pressure, drilling without clearing dust, or using a dull bit. Stop, let it cool, clear the hole and reduce pressure.

Do I need to pre-drill before using an anchor?

Yes. Concrete anchors require a pilot hole of a specific diameter and depth, and the hole must be clean before installation.

How deep can I drill with a cordless drill?

Depth depends on bit length and battery capacity. Most masonry bits used with cordless drills are sized for holes up to several inches deep, and deeper work takes more time and battery charge.

Should I use water when drilling concrete?

Water can help reduce dust and keep the bit cool on some jobs, but it is less common with cordless drills. Check your bit and anchor instructions before using liquid.

What if the hole is wandering off center?

Stop, mark the center again with a punch and restart at a lower speed. Holding the drill steady and starting slowly usually corrects the problem.

When should I hire a professional?

For structural work, rebar-heavy slabs, large openings or any job involving electrical or plumbing routes in concrete, consult a licensed contractor or engineer.

Conclusion

To drill concrete with cordless drill successfully, set hammer mode, use carbide masonry bits sized to your anchor, and let the tool do the work with steady pressure. Clear dust often, control exposure with extraction and a rated respirator, and watch for overheating. Follow these steps and your holes will come out clean, straight and ready for secure fastening.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our power tools guides, checking product details against manufacturer specifications and owner feedback.