Updated November 2026

Using a cordless drill comes down to four things: picking the right bit, setting the clutch and speed, holding the tool steady, and letting the bit do the work. Once you understand those basics, you can drill clean pilot holes, drive screws flush and avoid the most common stripped-head or cracked-material problems. This guide walks through each step in order.

Prepare the Drill and the Work

Start by confirming the battery is fully charged and seated firmly until it clicks. Next, check the chuck: a keyless chuck should tighten by hand, and a keyed chuck needs its key fully engaged in all three holes. Then mark your target with a pencil or center punch so the bit does not wander at the start.

Shopping for one? See our guide: 4 Best Cordless Impact Drill Driver Picks of 2026.

Secure the workpiece. Clamp it to a bench or place a scrap board underneath to prevent blowout on the exit side. Never hold small pieces by hand while drilling.

Choose the Right Bit and Settings

Match the bit to the material. Twist bits suit wood and metal, brad-point bits give cleaner wood holes, and masonry bits are needed for concrete or brick. Use a drive bit that matches the screw head to avoid cam-out.

Set the clutch collar to a number for driving screws, starting low and increasing until the screw seats without spinning. For drilling holes, switch to the drill setting, which locks the clutch so the bit keeps turning. Choose low speed for driving and large holes, and high speed for small holes in soft materials.

  1. Set the forward/reverse switch to forward.
  2. Select drill mode or a low clutch number for screws.
  3. Set speed: low for big bits and screws, high for small bits in wood.
  4. Place the bit tip on your mark and hold the drill perpendicular to the surface.
  5. Squeeze the trigger gently to start, then apply steady, moderate pressure.
  6. Withdraw the bit slowly while the drill is still running to clear chips.

Drill Holes and Drive Screws Correctly

Drilling Holes

Let the bit cut at its own pace. Pushing too hard can overheat the bit, glaze its edges and bind the drill. For deep holes in wood, pull the bit out every half inch or so to clear chips. In metal, a few drops of cutting oil extend bit life.

Driving Screws

Drill a pilot hole slightly smaller than the screw’s core diameter in hardwood, and a little larger in softwood. Drive the screw until the head sits flush, then stop. Hand-tightening the last turn prevents stripped threads and cracked wood.

Common Mistakes to Avoid

  • Leaving the clutch on a high setting, which strips screws and wears the driver bit.
  • Using a standard twist bit in masonry, which dulls quickly and produces little dust.
  • Forgetting to switch from driver to drill mode before boring holes.
  • Skipping eye and hearing protection, especially when drilling overhead or into concrete.
  • Running a nearly drained battery, which weakens torque and can overheat the tool.

A quality set of titanium-coated twist bits handles most wood and metal work, and a rugged drive bit set keeps screws from cam-out. For masonry, a dedicated set of carbide-tipped bits matches the tool’s torque to concrete.

  • Drill and driver bit set: covers most household drilling and screwdriving tasks. View on Amazon
  • Impact-rated driver bits: hold up better under high torque than standard bits. View on Amazon
  • Carbide masonry bit set: designed for drilling into concrete and brick. View on Amazon

FAQ

Should I use a cordless drill or an impact driver for screws?

A cordless drill works well for most screws in wood and soft materials, and its clutch protects fasteners. Impact drivers deliver more torque for long lag screws or dense hardwood, but they can overdrive small screws.

How do I stop the drill from slipping when starting a hole?

Make a center punch mark or start with a small pilot bit at low speed. Keep the drill steady and let the bit bite before increasing pressure.

Can I drill into tile with a standard bit?

Standard bits tend to skate across glazed tile. Use a carbide-tipped tile or masonry bit at low speed, with water or masking tape to keep the bit from wandering. Consult a professional for large or structural openings.

Conclusion

Using a cordless drill well depends on matching the bit to the material, setting the clutch correctly and keeping steady pressure. Practice on scrap wood before tackling finished work. Careful habits pay off with cleaner holes and better-seated screws.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our power tools guides, checking product details against manufacturer specifications and owner feedback.