Updated November 2026

A cutting granite circular saw job is manageable with the right blade, a steady water supply and a slow, controlled feed rate. This guide walks through the setup, the cut itself and the mistakes that cause chipping or cracked stone. Expect a clean, straight edge once you follow the steps in order.

Choose the Right Blade and Saw

Granite is one of the hardest natural stones, so a standard wood or metal blade will not work. You need a diamond blade rated for dry or wet stone cutting, and most manufacturers list the material on the blade label. A segmented rim cuts faster, while a continuous rim leaves a smoother edge with less chipping, which matters more for visible countertop work.

Shopping for one? See our guide: 5 Best DeWalt Circular Saw Battery Options for Cordless Cutting (2026).

Use a saw with a stable base and enough power for the job. Many people use a standard circular saw fitted with a diamond blade, but a dedicated wet saw is easier to control on long cuts. Check that the blade diameter matches your saw’s guard and arbor, and confirm the blade’s maximum RPM is at or above your saw’s speed.

Prepare the Stone and Your Workspace

Mark your cut line with painter’s tape on the top surface to reduce chipping. Support the slab fully on sawhorses or a flat bench so the cut does not pinch the blade. Keep the cutoff piece supported as well, since a sagging section can crack the remaining slab.

  1. Set the blade depth to about 1/8 inch deeper than the stone thickness.
  2. Wet the cut line and keep a steady water flow to the blade.
  3. Wear eye protection, a respirator rated for silica dust, hearing protection and cut-resistant gloves.
  4. Clear the area of cords and trip hazards, and keep a helper ready if the piece is heavy.

Cutting Granite with a Circular Saw: Step by Step

Cutting granite with a circular saw works best as a series of shallow passes rather than one deep plunge. Start the saw off the stone, bring it to full speed, then lower it onto the marked line. Let the blade do the work and avoid forcing it forward.

  1. Make a first pass about 1/8 inch deep to create a groove.
  2. Complete additional passes, deepening each one slightly, until you cut through.
  3. Keep water running on the blade throughout. Dry cutting overheats the diamonds and produces harmful dust.
  4. Move the saw at a steady, even speed. If the motor bogs down or the blade smokes, back off the pressure.
  5. Lift the saw out of the cut before turning it off so the blade stops clear of the stone.

Finishing the Edge

After the cut, rinse the stone and let the edge dry. Smooth any rough spots with a diamond polishing pad, working from coarse to fine grit. Take your time here, since the edge is what people notice first.

Common Mistakes to Avoid

  • Cutting dry, which overheats the blade and creates silica dust.
  • Plunging too deep in one pass, which causes chipping and stalls the motor.
  • Leaving the slab unsupported, which can crack the stone mid-cut.
  • Using a blade not rated for stone, which wears out quickly and cuts poorly.
  • Pushing too hard, which can overheat the saw and damage the blade segments.

A diamond blade made for granite is the most important purchase, since the wrong blade will not cut the stone. A water feed kit or hose attachment keeps the blade cool and the dust down. Clamps or a sturdy cutting table help keep the slab stable during the cut.

  • Diamond granite cutting blade for circular saws: rated for wet or dry stone cutting. View on Amazon
  • Water feed kit for circular saw stone cutting: keeps the blade cool and reduces dust. View on Amazon
  • Stone cutting table with clamps: holds the slab steady and supported. View on Amazon

FAQ

Can I use a regular circular saw for granite?

Yes, as long as you fit it with a diamond blade designed for stone. Standard wood or metal blades will not cut granite and can be dangerous to use on it. For another angle, check out Circular Saw for Aluminum Cutting: A Step-by-Step Guide for Clean Cuts.

Do I need water when cutting granite?

Water is strongly recommended. It cools the blade, reduces dust and extends blade life. Dry cutting creates silica dust, so a respirator is essential if you must cut without water.

How deep should each pass be?

Start with a shallow pass of about 1/8 inch, then deepen each pass gradually until you cut through. Check the blade manufacturer’s guidance for your specific model. If you want more background, see Circular Saw for Cutting 4×4: A Step-by-Step Guide for Clean Cuts.

Conclusion

Cutting granite with a circular saw comes down to the right diamond blade, steady water flow and shallow, controlled passes. Support the slab fully and wear proper protection before you start. Consult a professional stone fabricator for large or structural pieces.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our power tools guides, checking product details against manufacturer specifications and owner feedback.