Updated November 2026

A Craftsman compound miter saw cuts angles in two directions at once: side to side for the miter and tilted for the bevel. Once you know how to square the blade, lock the settings and clamp your stock, you can make clean, repeatable crosscuts for trim, framing and small projects. This guide walks through setup, cutting technique and the mistakes that most often ruin a cut.

Set Up the Saw Before Your First Cut

Start by placing the saw on a flat, stable surface, ideally a bench or stand with the table at a comfortable working height. Check that the base sits flat and the fence is firmly bolted down. Loose hardware is the most common reason a cut drifts.

Next, confirm the blade is sharp, clean and seated correctly. Make sure the blade guard moves freely and returns on its own. Unplug the saw before you touch the blade or adjust any settings.

Check and Adjust the Miter and Bevel Stops

Most Craftsman compound saws have detents, the positive stops that snap the miter table to common angles like 0, 15, 22.5 and 45 degrees. Check these with a reliable square and a test cut before trusting them.

  1. Set the miter to 0 degrees and lower the blade. Place a combination square against the blade and the fence.
  2. If the blade is not square to the fence, use the adjustment screws or the manufacturer’s procedure to bring it into alignment.
  3. Make a test cut on a scrap board. Flip both halves together and check whether they meet tightly.
  4. Repeat for the bevel stop at 0 degrees, adjusting the bevel stop screw as needed.

Your manual lists the exact adjustment points for your model. If you are unsure which screws to turn, consult the manual or a qualified repair technician before forcing anything.

Make the Cut Safely and Accurately

Hold the workpiece firmly against the fence and flat on the table. Keep your hands at least several inches from the blade path, and use a clamp for any piece too short to hold safely. Let the blade reach full speed before lowering it into the wood. We also found 6 Best Craftsman Table Saw Table Options for Home Shops (2026) useful on this point.

Lower the blade in one smooth motion, pulling it through the cut rather than pushing hard. Let the saw do the work. Wait for the blade to stop completely before lifting it or removing the offcut.

Cutting Compound Angles

A compound cut sets both the miter and bevel at once. This is the usual method for crown molding, which sits at an angle against the wall and ceiling. Check your molding’s spring angle and the saw’s compound chart, then test on scrap before cutting finished stock. Small errors in either angle add up quickly.

Tools and Supplies You Will Need

  • A combination square or speed square for checking alignment
  • Clamps to hold workpieces securely
  • A sharp blade matched to the material
  • Scrap wood for test cuts
  • Safety glasses and hearing protection

Common Mistakes

  • Skipping the square check after moving the saw or changing blades.
  • Trusting the detent stops without verifying them with a test cut.
  • Cutting with a dull or dirty blade, which causes tear-out and binding.
  • Letting short offcuts flop around near the blade instead of clamping them.
  • Mixing up the miter and bevel directions on compound cuts.

A sturdy stand or extension wings help support long boards so the stock stays level through the cut. View on Amazon

A quality combination square makes checking blade alignment faster and more reliable. View on Amazon

Replacement blades matched to your material keep cuts clean and reduce burning. View on Amazon

FAQ

How do I know if my Craftsman compound miter saw is square?

Set the miter and bevel to 0 degrees, then check the blade against a reliable square and make a test cut. If the two pieces do not meet tightly when flipped, adjust the stops following your manual.

Can I cut crown molding with a compound miter saw?

Yes. Crown molding is typically cut with compound settings, using the spring angle of the molding and a test piece to confirm the angles. For more detail, see Miter Saw to Cut Crown Molding: Angles, Settings and Tips (2026).

How often should I replace the blade?

Replace or sharpen the blade when cuts start to tear out, burn or require extra force. Blade life depends on the material and how often you use the saw. For blade selection basics, see Saw Blades: Tooth Count, Kerf and Grind for Circular, Miter and Table Saws.

Conclusion

With the saw checked for square, the stops verified and the workpiece secured, a Craftsman compound miter saw delivers accurate, repeatable angles. Take time on setup and test cuts, and the actual cutting will go quickly. If you are comparing models, see Craftsman Compound Miter Saw 10 Inch: 3 Best Picks Compared (2026).

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our power tools guides, checking product details against manufacturer specifications and owner feedback.