Updated November 2026
A makita cordless drill hammer lets you drill into brick, block and concrete without a corded tool or a separate rotary hammer. This guide explains what the hammer function does, how to match a Makita model to your materials, and how to drill clean, safe holes. Most of the work comes down to picking the right mode and bit.
What the Hammer Function Actually Does
In hammer mode, the chuck rapidly pushes the bit forward while it spins, so each rotation chips at masonry instead of grinding against it. Standard drill mode is for wood, metal and plastic. Hammer mode is for masonry. Running a hammer drill in plain drill mode into concrete will overheat the bit and wear out the tool quickly.
Shopping for one? See our guide: Milwaukee M18 FUEL Cordless Hammer Drill: 9 Best Picks for Concrete and Masonry.
Most Makita cordless hammer drills offer a mode selector ring near the chuck. Check the ring before every job, because it is easy to leave it in the wrong setting.
How to Choose the Right Makita Model
Start with the material you drill most. A compact drill with a hammer setting handles occasional anchor holes in block or brick. Heavier masonry work, such as drilling many holes into poured concrete, calls for a larger hammer drill with more impact energy.
- Light home use: a 12V or 18V compact hammer drill for shelf brackets and small anchors.
- General masonry: an 18V hammer drill with a brushless motor for longer run time.
- Heavy concrete: a rotary hammer, which uses a separate piston mechanism rather than a clutch-based hammer action.
Check whether your Makita battery platform already has a hammer drill you can use with batteries you own. Buying into a platform you already use saves money on batteries and chargers.
Step-by-Step: Drilling Into Masonry
- Set the mode selector to hammer drill and confirm the clutch is set to drill, not screwdriver.
- Insert a carbide-tipped masonry bit that is fully seated and tightened in the chuck.
- Mark the hole, then start at low speed with the bit at a right angle to the surface.
- Apply steady, moderate pressure. Let the hammer action do the work rather than pushing hard.
- Pull the bit out every 15 to 20 seconds to clear dust, especially on deeper holes.
- Stop when you reach the depth you need, then vacuum the hole before inserting an anchor.
Wear eye protection and a dust mask rated for masonry dust, since drilling concrete releases crystalline silica. For structural or load-bearing work, consult a professional before drilling into concrete.
Bit and Battery Tips for Better Results
| Material | Bit type | Mode |
|---|---|---|
| Brick or block | Carbide masonry bit | Hammer |
| Poured concrete | Carbide masonry bit, SDS shank if using a rotary hammer | Hammer |
| Wood or metal | Standard twist or spade bit | Drill only |
Keep the battery charged to a full level before starting, because a weak battery slows the hammer action and causes stalling. If you are new to the platform, Using a Cordless Drill: A Step-by-Step Guide for Beginners covers basic handling that applies here too.
Common Mistakes
- Leaving the mode selector in drill-only mode when drilling masonry.
- Pressing too hard, which bogs the motor and dulls the bit.
- Skipping dust clearing, which makes the bit bind and overheat.
- Using a wood bit in masonry, which will skate across the surface.
- Continuing to drill after the tool gets very hot; let it cool before resuming.
Recommended Gear
A set of carbide masonry bits in the sizes you use most saves time on anchor holes. View on Amazon
A depth stop or tape on the bit helps you hit consistent hole depths for anchors. View on Amazon
A hole vacuum or hand pump clears dust from deep holes before you set an anchor. View on Amazon
Related Reading on Choosing Hammer Drills
If you are comparing platforms, Milwaukee vs Dewalt Cordless Drill (2026): Which Should You Choose? sets out the trade-offs. For heavier concrete work, 7 Best Cordless Rotary Hammer Drills for Concrete and Masonry: Expert Picks covers the step up from a clutch-based hammer drill. Anyone buying a full kit may also find Makita Cordless Drill Sets: How to Choose the Right Kit (2026) useful.
FAQ
Can a makita cordless drill hammer replace a rotary hammer?
For light to moderate masonry, such as anchors in brick and block, a hammer drill works well. For heavy concrete or frequent large-diameter holes, a rotary hammer is the better tool.
Do I need a special bit for hammer mode?
Yes. Use carbide-tipped masonry bits. Standard wood or metal bits will dull quickly and may not cut effectively in hammer mode.
How do I know if the hammer function is on?
Check the mode selector ring near the chuck. When set to hammer, you will feel a rapid pulsing action when the trigger is pressed under load.
Conclusion
A makita cordless drill hammer handles most home masonry jobs once you set the right mode and use carbide bits. Match the tool to your typical materials, clear dust often, and let the impact do the work. With those habits, you will drill cleaner holes and get longer life from both the bit and the battery.

